How do I build a flightcase without rivets?

Building a flightcase without rivets utilises alternative fastening methods that offer easier assembly and future serviceability. The Adam Hall Easy-Case system employs hybrid aluminium profiles with integrated T-slot channels – panels slide into grooves and secure via set screws or spring clips, eliminating drilling entirely. Alternatively, bolted construction using M6 or M8 machine screws with T-nuts or cage nuts through corner braces and L-brackets provides strong, disassemblable joints. This approach works particularly well for 19-inch rack cases requiring precise alignment. For panel-to-profile connections, wood screws (4×16mm or 4×20mm) driven through pre-drilled aluminium profiles into plywood edges create secure bonds without specialised rivet tools. Combining methods strategically – bolted structural corners, screwed profiles, adhesive-bonded foam – produces professional results accessible to builders without rivet gun equipment.

Which materials are best for professional case construction?

Professional flightcase construction relies primarily on birch multiplex plywood in 9mm or 12mm thicknesses, offering optimal screw-holding strength, impact resistance and weight-to-strength ratio. Birch plywood bonded with D4 adhesive (per DIN EN 204) provides water resistance essential for outdoor event applications. For weight-critical touring applications, SolidLite panels – aluminium-skinned honeycomb composites – reduce case weight by 30–40% whilst maintaining structural integrity, though they require through-bolting with large washers rather than edge-screwing. Aluminium profiles should specify 6060 or 6063 T6 alloy in appropriate dimensions: 22×22mm for lightweight cases, 25×25mm for medium-duty applications, 30×30mm for heavy touring equipment. Steel hardware (corners, latches, hinges) requires zinc plating or powder coating for corrosion resistance. Interior protection demands layered foam systems: firm polyethylene base foam, shock-absorbing convoluted middle layers, and soft polyurethane contact foam.

What tools do I need for case building?

Essential case building tools include a jigsaw or circular saw for cutting plywood panels to dimension, a drill or cordless driver (minimum 18V for sustained use) with stepped drill bits for aluminium profiles and wood bits for panel pre-drilling, and a rivet gun (hand-operated or pneumatic) if using traditional riveted construction. Measuring and marking tools – steel ruler (minimum 1000mm), carpenter's square and marking knife – ensure accurate dimensions. For rivet-free construction, a tap and die set (M6 and M8 threads) and appropriate Allen keys or socket drivers suffice. Specialised tools enhance results: a router with flush-trim bit creates clean laminate edges, a mitre saw produces precise 45° profile cuts for corner joints, and spring clamps (minimum six) hold assemblies during fastening. Safety equipment – hearing protection, safety glasses and dust mask – remains mandatory. For foam work, a sharp utility knife or hot-wire cutter (for precise custom profiles) completes the toolkit. Total investment for comprehensive capability ranges €300–800 depending on power tool quality.

Are the fittings rust-proof and suitable for touring?

Professional case building fittings from manufacturers like Penn Elcom and Adam Hall incorporate corrosion-resistant surface treatments specifically engineered for touring conditions. Zinc-plated steel components (the industry standard) provide excellent protection against humidity, salt air and temperature cycling encountered during road transport and outdoor events. Powder-coated variants add an additional protective layer whilst offering aesthetic colour options. Stainless steel springs in butterfly catches and latches resist corrosion even in coastal or high-humidity environments. However, "rust-proof" remains conditional: prolonged exposure to standing water, de-icing salt or marine environments will eventually compromise any finish. Regular maintenance – wiping down fittings after outdoor use, occasional application of silicone spray to moving parts – extends service life significantly. For extreme conditions (tropical touring, marine applications), specify stainless steel fittings throughout despite higher cost. Quality fittings from established manufacturers typically provide 5–10 years of reliable touring service with basic maintenance, whilst budget alternatives may show corrosion within 1–2 seasons.

Can I use case hardware to repair existing flightcases?

Case building accessories excel at repairing and refurbishing existing flightcases, often extending service life by years at modest cost. The industry-standard dimensions of Penn Elcom and Adam Hall components ensure compatibility with most professionally built cases regardless of original manufacturer. Common repairs include replacing worn butterfly catches (typically failing after 500–1000 open/close cycles), upgrading basic wheels to ball-bearing castors for improved manoeuvrability, retrofitting lift-off hinges for easier lid removal, and replacing damaged corner protectors. Structural repairs may require removing rivets (drill out with 4mm or 5mm bit), installing new aluminium profiles and re-riveting or bolting. Interior refurbishment – replacing compressed foam, adding pick-and-pluck inserts for new equipment profiles, installing additional rack rails – transforms generic cases into equipment-specific solutions. Before purchasing repair components, measure existing fittings carefully: butterfly catch backplate dimensions, wheel mounting hole spacing (typically 60×80mm or 80×100mm), and profile cross-sections vary between manufacturers. Photographing damaged components aids identification. Repair economics favour professional cases: a €50 hardware refresh on a quality case proves more cost-effective than €200+ for new construction.

What is the difference between ball corners and stacking corners?

Ball corners and stacking corners serve distinct functional purposes in flightcase construction. Ball corners (also called radius corners or round corners) feature a spherical profile that distributes impact forces across a curved surface, providing maximum protection for case edges and contents during handling and transport. Available in small (25mm radius), medium (35mm) and large (50mm) variants, they suit general-purpose cases where impact resistance outweighs stacking requirements. Stacking corners incorporate a recessed profile or interlocking geometry that allows cases to nest securely when stacked vertically. The recessed upper surface accepts the protruding lower corner of the case above, preventing lateral movement during truck transport. This feature proves essential for touring operations where multiple cases stack in transport vehicles – without interlocking geometry, vibration and acceleration forces cause stack shifting and potential damage. Some professional corners combine both features: a stackable profile with radiused impact surfaces. Selection depends on application: FOH mixing console cases benefit from maximum-radius ball corners for protection, whilst identical monitor speaker cases in sets of eight require stacking corners for secure truck pack configuration.

How do I integrate 19-inch rack rails into a custom case?

Integrating 19-inch rack rails into custom flightcase construction requires precise measurement and secure mounting to ensure equipment compatibility and structural integrity. Standard rack rails (punched or threaded variants) mount vertically at exactly 450mm spacing (centre-to-centre) to accommodate 19-inch equipment widths of 482.6mm. Begin by marking rail positions on case interior side panels, ensuring vertical alignment using a spirit level – even 2–3mm deviation causes equipment mounting difficulties. Cage nuts (M6 thread) or rivnuts installed in punched rack rails accept standard rack screws; threaded rails eliminate this step but cost more. Secure rails using M6 bolts with large washers (minimum 20mm diameter) through case panels into rail mounting holes, spacing fasteners every 3–4 rack units for rigidity. For plywood cases, through-bolting provides maximum strength; SolidLite panels require backing plates to distribute loads across the honeycomb core. Front and rear rail pairs create complete rack systems; single front-rail mounting (with rear equipment support brackets) suits mixer cases where rear access remains necessary. Rack depth typically ranges 400–600mm depending on equipment; measure the deepest unit before finalising case dimensions. Adding rack shelves between equipment creates cable management space and prevents vertical load stacking.

What foam thickness should I use for equipment protection?

Selecting appropriate foam thickness for flightcase interior protection depends on equipment fragility, case size and shock absorption requirements. 10mm soft foam serves as general-purpose lining for case lids and base panels, providing scratch protection and light cushioning for robust equipment like amplifiers or lighting fixtures. 20mm foam offers moderate shock absorption suitable for mixers, controllers and similar electronics where impact protection matters but space remains limited. 30mm foam layers (or 20mm + 10mm combinations) provide substantial protection for delicate equipment: microphones, cameras, measurement instruments and glass-fronted devices benefit from this thickness. Pick-and-pluck foam typically comes in 30mm or 50mm blocks with 10mm cube grids, allowing custom equipment profiles – thicker blocks suit larger items with complex shapes. For maximum protection, specify layered systems: firm 10mm polyethylene base (prevents equipment "bottoming out" on hard case floor), 20–30mm convoluted middle layer (absorbs shock through air-filled peaks), and 10mm soft polyurethane top layer (gentle equipment contact). Total foam thickness should not exceed 40% of case interior depth to maintain usable equipment space. Foam density matters equally: specify 25–30 kg/m³ for general padding, 35–40 kg/m³ for structural support and equipment retention.

Close menu

LTT-Versand englisch

Case accessories

Top seller

Bralo 55964814 - Gerillter Blindniet aus Aluminium / Stahl 4,8 x14 mm

Bralo 55964814 - Grooved blind rivet made of aluminium / steel 4.8 x14 mm

€0.10 *

incl. tax, plus shipping costs